RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049317 ROOF HEADLINING A

INTERIOR PANELS / TRIM ROOF HEADLINING REMOVAL

PROCEDURE

Hide Display 1. PRECAUTION

NOTICE:: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.; Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION201212,201410,_V1,_008731,_0049918,RM1000000004DZ6,201410,201504,_V1,_008731,_0049918,RM100000000HFP9,201504,201510,_V1,_008731,_0049918,RM100000000JQM7,

Hide Display 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:: When disconnecting the cable, some systems need to be initialized after the cable is reconnected.; Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION201212,201311,_V1,_008731,_0049918,RM1000000004DZ8,201311,201410,_V1,_008731,_0049918,RM100000000C1G2,201410,201504,_V1,_008731,_0049918,RM100000000HFOT,201504,201510,_V1,_008731,_0049918,RM100000000JQM8,

Hide Display 64309A 3.REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

Release the 4 locks and remove the package tray trim pocket sub-assembly.

Hide Display 64910N 4.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Release the 2 locks and remove the tonneau cover assembly.

Hide Display 58410B 5.REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire, for Compact Spare Tire)

Remove the deck board assembly.

Hide Display 58410B 6.REMOVE DECK BOARD ASSEMBLY (w/ Full Size Spare Tire)

Remove the deck board assembly.

Hide Display 64997 7.REMOVE DECK FLOOR BOX LH

Using a clip remover, remove the 3 clips.

Detach the 4 claws and remove the deck floor box LH.

Hide Display 58386 8.REMOVE REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

Detach the 2 claws, 4 clips and 2 guides and remove the rear floor finish plate.

Hide Display 64716P 9.REMOVE REAR DECK TRIM COVER (w/ Full Size Spare Tire)

Detach the 3 claws and 4 clips and remove the rear deck trim cover.

Hide Display 58577E 10.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/o Spare Tire, for Compact Spare Tire)

Open the rear No. 1 floor board.

Remove the 4 screws.

Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.

Hide Display 58577E 11.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/ Full Size Spare Tire)

Open the rear No. 1 floor board.

Remove the 4 screws.

Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.

Hide Display 12.REMOVE REAR SEAT ASSEMBLY

for LH Side:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for LH Side)>REMOVAL201212,201510,_58,_008433,_0049737,RM1000000004CGJ,

for RH Side:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for RH Side)>REMOVAL201212,201510,_58,_008433,_0049738,RM1000000004CGP,

Hide Display 67914B 13.REMOVE FRONT DOOR SCUFF PLATE LH

Detach the 8 claws and 2 clips and remove the front door inside scuff plate LH.

Hide Display 67913B 14.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:: Use the same procedure described for the LH side.

Hide Display 62312B 15.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Remove the front door opening trim weatherstrip LH.

Hide Display 62311B 16.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:: Use the same procedure described for the LH side.

Hide Display 67918E 17.REMOVE REAR DOOR SCUFF PLATE LH

Detach the 2 claws and 6 clips and remove the rear door scuff plate LH.

Hide Display 67917C 18.REMOVE REAR DOOR SCUFF PLATE RH

HINT:: Use the same procedure described for the LH side.

Hide Display 62332C 19.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Remove the rear door opening trim weatherstrip LH.

Hide Display 62331C 20.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:: Use the same procedure described for the LH side.

Hide Display 64740E 21.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Remove the screw and 2 bolts.

Remove the bolt and disconnect the rear seat outer belt floor anchor.

Open the tether anchor set bracket cover.

Remove the bolt and tether anchor set bracket.

Remove the bolt and luggage hold belt striker assembly.

Detach the 6 claws and 4 clips and remove the deck trim side panel assembly LH.

Disconnect the connector.

Hide Display 64730J 22.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Remove the screw and 2 bolts.

Remove the bolt and disconnect the rear seat outer belt floor anchor.

Open the tether anchor set bracket cover.

Remove the bolt and tether anchor set bracket.

Remove the bolt and luggage hold belt striker assembly.

Detach the 6 claws and 4 clips and remove the deck trim side panel assembly RH.

Hide Display 73178A 23.REMOVE SEAT BELT ANCHOR COVER CAP

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY>REMOVAL201212,201510,_58,_008788,_0050329,RM1000000004F7I_02_0067,

Hide Display 62480A 24.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Remove the bolt and disconnect the rear seat outer belt shoulder anchor.

Detach the 8 clips and remove the inner roof side garnish assembly LH.

Hide Display 62470A 25.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT:: Use the same procedure described for the LH side.

Hide Display 73135A 26.REMOVE SHOULDER BELT ANCHOR COVER RH

Click hereVehicle Interior>SEAT BELT>REAR CENTER SEAT OUTER BELT ASSEMBLY>REMOVAL201212,999999,_58,_008788,_0050330,RM1000000004F7M_01_0007,

Hide Display 73233 27.REMOVE OUTER LAP BELT ANCHOR COVER

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL201212,999999,_58,_008788,_0050327,RM1000000004F7A_02_0034,

Hide Display 62414A 28.REMOVE LOWER CENTER PILLAR GARNISH LH

Remove the bolt and disconnect the front seat outer belt floor anchor.

Detach the 2 clips and 2 claws and remove the lower center pillar garnish LH.

Hide Display 62413A 29.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:: Use the same procedure described for the LH side.

Hide Display 62412 30.REMOVE CENTER PILLAR GARNISH LH

Remove the 2 clips.

Detach the clip and remove the center pillar garnish LH.

Pass the front seat outer belt floor anchor through the hole of the center pillar garnish LH.

Hide Display 62411 31.REMOVE CENTER PILLAR GARNISH RH

HINT:: Use the same procedure described for the LH side.

Hide Display 62212 32.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 clips.

Detach the 3 guides and remove the front pillar garnish LH.

Hide Display 62211 33.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 62212 34.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

1.906,0.354 2.198,0.354 2.198,0.354 2.385,0.74 false 1.74,0.271 2.052,0.469 0.313,0.198 10 *1

*1	Front Pillar Garnish Clip

Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 front pillar garnish clips.

HINT:: Make the front pillar garnish LH hang down from the front pillar garnish clip.

2.365,0.417 2.469,0.219 2.469,0.219 2.656,0.219 false 2.677,0.146 2.99,0.344 0.313,0.198 10 *1

*1	Front Pillar Garnish Clip
	Protective Tape

Turn the ends of the 2 front pillar garnish clips 90° with needle-nose pliers and disconnect them from the front pillar garnish LH.

HINT:: Tape the tips of the needle-nose pliers before use.

Detach the 3 guides and remove the front pillar garnish LH.

1.448,0.156 1.625,0.302 0.177,0.146 10 true A

While pulling the front pillar garnish clip in direction A with a finger, insert a screwdriver at the position shown in the illustration.

0.844,0.167 1,0.344 0.156,0.177 10 true B

While pulling the front pillar garnish clip in direction B with a finger, insert a screwdriver at the position shown in the illustration to detach the front pillar garnish clip.

NOTICE:: If the front pillar garnish clip is damaged, replace it with a new one.

1.365,2.188 1.615,2.188 1.615,2.188 1.875,1.979 true 1.854,2.969 2.188,2.969 2.188,2.969 2.427,2.688 true 1.198,2.083 1.51,2.281 0.313,0.198 10 false *1 1.698,2.854 2.01,3.052 0.313,0.198 10 false *2

*1	Curtain Shield Airbag Assembly LH
*2	Protective Cover
	Adhesive Tape

Protect the curtain shield airbag assembly LH.

Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:: Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.

Hide Display 62211 35.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 36.REMOVE UPPER INSTRUMENT PANEL

Click hereVehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>REMOVAL201212,201510,_58,_008791,_0049314,RM10000000048VT,

Hide Display 74320 37.REMOVE VISOR ASSEMBLY LH

Remove the 2 screws and visor assembly LH.

Hide Display 74310 38.REMOVE VISOR ASSEMBLY RH

HINT:: Use the same procedure described for the LH side.

Hide Display 74348 39.REMOVE VISOR HOLDER

HINT:: Use the same procedure for both visor holders.

Turn the visor holder clockwise approximately 45° and pull it as shown in the illustration.

Detach the 2 claws and remove the visor holder.

Hide Display 81260A 40.REMOVE MAP LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL201212,201510,_58,_008429,_0050312,RM1000000004F56_01_0001,

Hide Display 74610A 41.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:: Use the same procedure for all assist grips.

0.833,0.24 1.042,0.49 0.208,0.25 10 false .

Protective Tape

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:: Tape the screwdriver tip before use.

Detach the 2 clips and remove the assist grip sub-assembly.

Hide Display 81240 42.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL201212,999999,_58,_008429,_0050313,RM1000000004F5A_01_0001,

Hide Display 87834 43.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Detach the 8 claws and remove the inner rear view mirror stay holder cover.

Hide Display 63318C 44.REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

Remove the sun roof opening trim moulding.

Hide Display 63310 45.REMOVE ROOF HEADLINING ASSEMBLY

w/ EC Mirror:

Disconnect the connector.

w/ Sliding Roof:

Disconnect the connector.

Disconnect the connector from the rear pillar RH.

Disconnect the 2 connectors and detach the 3 clips and 3 wire harness clamps from the front pillar LH.

Detach the 4 wire harness clamps from the front pillar RH.

1.167,2.542 1.479,2.74 0.313,0.198 10 *A 2.073,2.531 2.385,2.729 0.313,0.198 10 *A

*A	w/o Sliding Roof

w/o Sliding Roof:

Remove the 5 clips.

w/ Sliding Roof:

Remove the 3 clips.

Remove the roof headlining assembly as shown in the illustration.

NOTICE:: Be careful not to damage the roof headlining assembly when taking it out.

Hide Display 66423A 46.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

Detach the 4 clips and remove the front side rail spacer LH.

Hide Display 66413C 47.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 66424 48.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

Detach the 4 clips and remove the rear side rail spacer LH.

Hide Display 66414A 49.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 66424 50.REMOVE REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

HINT:: When removing or replacing the rear side rail spacer LH, be sure to remove the curtain shield airbag assembly LH.; Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL201212,999999,_58,_008786,_0050513,RM1000000004FWE_02_0004,

Remove the bolt.

Detach the clip and remove the rear side rail spacer LH.

Hide Display 66414A 51.REMOVE REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 66425B 52.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

Detach the 3 clips and remove the No. 2 rear side rail spacer LH.

Hide Display 66415B 53.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

Hide Display 66425B 54.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

1.99,3.76 2.208,3.76 false 2.104,2.99 2.323,2.99 false 1.948,2.917 2.26,3.115 0.313,0.198 10 *1 1.823,3.688 2.135,3.885 0.313,0.198 10 *2

*1	Pin
*2	Clip

Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and pull out the pin from the clip.

Using 2 screwdrivers, detach the 2 claws by inserting the screwdrivers into the grooves of the clip as shown in the illustration, and then remove the clip from the vehicle body and disconnect the rear part of the curtain shield airbag assembly LH.

Detach the wire harness clamp.

Detach the 2 clips and remove the rear No. 2 side rail spacer LH.

Hide Display 66415B 55.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

HINT:: Use the same procedure described for the LH side.

FaceBox